Always keep the battery cables and terminals clean and free of corrosive build-up. In some instances, the tractor may be driven in slippery or low-traction situations and it may be necessary to activate the differential lock. To connect the battery cables, proceed as follows: NOTE: The positive battery terminal is marked Pos. Pull the PTO switch up/out into the engaged (ON) position. To raise the left side of the deck, loosen the upper nut on the end of the lift rod, then turn the lower nut clockwise. 2. Installing the Front Bumper (If equipped):The hardware for attaching the front bumper is shipped installed into the bumper. This is normal. Remove the oil fill cap/dipstick from the oil fill tube. Activating the PTO engages power to the cutting deck or other (separately available) attachments. NOTE: The system should only be used when poor traction is encountered. Allow the machine to cool in an open area before storing. The further forward the pedal is pivoted, the faster the tractor will travel. One of the best ways to keep your tractor running efficiently and to reduce fire risk is to regularly remove debris buildup from the tractor. If the charger is not automatic, charge for no fewer than eight hours. 427K views 8 years ago Repairing a Craftsman riding lawn mower? AG front tires-AG rear tires-Lawn front tires: 16x6.5-8: Lawn rear tires: 16x6.5-8: . Tilting can cause fuel or oil leakage. Be sure engine is outdoors and in a well-ventilated area. To change the direction of travel from forward to reverse when cruise control is engaged, press the brake pedal to disengage and bring the tractor to a complete stop. NOTE: Cruise control can NOT be engaged at the tractors fastest ground speed. Craftsman CMXGRAM1130047 54-in 24.0 HP* Hydrostatic Riding Mower (T310) - Use Manual - Use Guide PDF. LO/BATT/TIME is displayed on the LCD when the voltage drops below 11.5 volts. WARNING: Never leave a running machine unattended. Repeat steps 1-4 to engage. To lower the front of the deck, loosen the outer nut then loosen (thread outward) the nut, away from the front hanger bracket. NOTE: Do not engage the mower deck when lowered in grass. 3. Page information: WARNING Gasoline is extremely flammable and can be explosive under certain conditions. Whilst this product is not eligible, further information about our warranties can be located below. NOTE: If the positive battery cable is already attached, skip ahead to step 2. Carefully remove the belt from around the PTO pulley. Push the PTO handle forward into the engaged (ON) position. To prevent gum deposits from forming inside the engines carburetor and causing possible malfunction of the engine, the fuel system must be either completely emptied, or the gasoline must be treated with a stabilizer to prevent deterioration. Turn Tight radius. Always shut off fuel flow when storing or transporting if tractor is equipped with a fuel shutoff. Release the key into the NORMAL MOWING MODE positi on once the engine has fire d. T o s top the engine, turn t he ignition key counterc lockw ise to the STOP positi on. Throttle is not meant to control unit speed, throttle should remain in high speed while operating blades. Start the tractor (as instructed in the Operation section of this manual). (). Refer to the Assembly & Set-Up section of this manual for seat adjustment instructions. DO NOT use E85 gasoline. If it doesnt, the parking brake is not engaged. %PDF-1.5 % Find parts and product manuals for your Craftsman T310 Turn Tight Riding Mower CMXGRAM1130047. If the interlock system should ever malfunction, do not operate tractor. After refueling, make sure the tank cap is closed properly and securely. A new oil filter catches damaging dirt and debris. On intervals that are common with oil service, the oil message will be displayed first followed by the air filter message. NOTE: The brake pedal must be fully depressed to activate the safety interlock switch when starting the tractor. Craftsman CMXGRAM1130047 | Series: T200 SERIES, T300 SERIES | Pages: 64 | Created on: 2019-01-21 | File type: PDF | Filename: Craftsman CMXGRAM1130044 T240 Turn Tight 22-HP V-twin Hydrostatic 46-i Craftsman CMXGRAM211303 Turn Tight AGM STZ12 Battery Start-HP V-Twin H Craftsman 917255915 6-speed garden tractor. If it doesnt, the cruise control is not engaged. Cutting Blades: To remove the blades, proceed as follows. Refer to the Assembly & Set-Up section for instructions on adjusting the seat position. Press the brake pedal completely down with your left foot and hold it in that position. 0000014185 00000 n When the proper adjustment is achieved, tighten the upper nut to secure in place. To start the engine, insert the key into the ignition switch and turn clockwise to the START, To stop the engine, turn the ignition key counterclockwise to the STOP, CAUTION: Prior to operating the tractor, refer to both Safety Interlock Switches and Starting The Engine in the Operation section of this manual for detailed instructions regarding the Ignition Switch Module and operating the tractor in REVERSE CAUTION MODE. This front engine riding mower is designed for the homeowner with demanding yard needs. These transmissions are very easy to use. If any fuel is spilled, make sure the area is dry before starting the engine. Privacy Policy. Our DIY how-to guides and videos to find repair instructions. Acid levels cannot be checked and fluid can not be added. Fill tank with clean, fresh gasoline and replace fuel filter. NOTE: Cruise control can not be set at the tractors fastest ground speed. Engage the parking brake. 0000014567 00000 n (T310) Support. 59 46 But, theres so much more, including invitations to participate in exclusive contests and product sampling opportunities. In the following section, you will discover a lot more information about Craftsman T310 Lawn Tractor. You can unsubscribe at any time. Used under license Visit our website: www.craftsman.com The deck is properly leveled when both blade tip measurements taken earlier are equal. Turning up a slope greatly increases the chance of a roll over. Check the fuel and oil levels in the lawn mower. If a turn must be made, turn down the slope. The throttle/choke control lever is located on the left side of the tractors dash panel. Adjust if necessary as follows: Leveling the Deck (Side-to-Side): If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Always wear safety glasses during operation or while performing any adjustments or repairs, Use manuals file type: PDF. The transmission bypass rod is located at the rear of the tractor on the lower right section of the frame. Place the PTO in the disengaged (OFF) position. Disengage the PTO and raise the deck to the highest position before crossing. Follow the recommendations below and contact your authorized dealer with any questions. Fill the fuel tank with treated fuel and run the engine for 2-3 minutes to get stabilized fuel into the carburetor. The transmission bypass rod is located on the rear of the tractor, on the frame. Control the ground speed with forward drive pedal. RESISTS WEAR: Belts are manufactured using specifically engineered materials, including high-strength tensile cords designed to resist wear and provide superior durability. Crank engine with throttle in FAST position. Craftsman - Tools - Home Improvement, Copyright 2023 ManualsFile.com. Immediate repair and cleaning up oil or fuel spills can help reduce fire hazards. NOTE: Place an absorbent towel beneath the oil filter to keep oil off the clutch. Pull the right side of the belt and place the narrow V side of the belt into the PTO pulley, 9. After each operation of the tractor, the following procedures should be implemented to extend the life of your tractor and ensure safe operating conditions. Refill with clean, fresh gasoline. Login. The Operator's Manual is an important part of your new outdoor power equipment. Product Overview Replacement oil filter for Kohler, Command, Aegis, Courage and Triad/OHC Engines using part #: 12 050 01-S and 7124604 Applications Riding Mowers Includes Use care to avoid burns from hot oil. Craftsman T260 CMXGRAM1130045, Craftsman T310 CMXGRAM1130047 VS If your battery charger is automatic, charge the battery until the charger indicates that charging is complete. Add oil as necessary. Store mower in a dry, clean area. To raise the front of the deck, loosen the outer nut then tighten (thread inward) the nut against the front hanger bracket. Refer to Tires on page 11 for information regarding tire pressure. WARNING: Never engage the cruise control lever while traveling in reverse. The app will prompt you to enter your riding mowers model number and serial number. If it is necessary to stop while driving up a slope, start up smoothly and carefully to reduce the possibility of flipping the tractor over backward. 6. Remove the jumper cables in reverse order of connection. Craftsman T310 Lawn Tractor can generate energy up to 24 horsepower. After cleaning your deck with the Smart Jet system, return to the operators position and engage the PTO. Empty cargo boxes, grass catchers or containers. %%EOF Photos: No photos of the Craftsman T310 are currently available. Refuel in a well-ventilated area with the engine stopped. Remove the front and rear deck wheels by removing the flange lock nuts and shoulder bolts that secure them to the deck. Bagging helps to foster lawn growth by preventing thatch from building up. Clean and lubricate the unit thoroughly as described in the Lubrication instructions in the Service and Maintenance section. The letters LO will display followed by the letters BATT and then followed by the meters accumulated time. 0000010424 00000 n This riding mower also includes a front-end bumper for added safety. If the tractor does not come to a complete stop when the brake pedal is completely depressed, or if the tractors rear wheels can roll with the parking brake applied (and the hydrostatic relief valve open), the brake is in need of adjustment. Refer to the Operation section of this manual for detailed instructions regarding the parking brake. Using an approved red GASOLINE container, add fuel slowly, being careful to avoid spilling. Locate the fuel filter, which is located on the left side of the engine, and may be attached to the engine with a tie strap. To travel in REVERSE, check that the area behind is clear then slowly depress the reverse drive pedal until the desired speed is achieved. Fuel leaks/spills, oil leaks/spills and excess lubrication can also become collection sites for debris. Privacy Policy. Have the apparent starting issue and low battery issue been remedied in the 2020 model production for this model? 24.0 HP* Hydrostatic TURNTIGHT Gas Riding Mower (T310). The CRAFTSMAN® T3200 front engine riding mower is designed for the homeowner who needs to accomplish more. Plus there several others too. NOTE: On some decks it may be necessary to remove the spindle covers to remove and/or install the new belt. Move the tractor on a firm and level surface, preferably pavement, and proceed as follows: NOTE: Refer to Adjusting the Deck in the Maintenance & Adjustments section of this manual for more detailed instructions regarding various deck adjustments. Craftsman is a brand that a lot of people trust when it comes to powerful residential lawn mowers. Before the interval expires, change the engine oil as instructed in the Maintenance section of the Engine Operators Manual. 815 Instruction Manuals and User Guides for Craftsman online. In addition to cleaning the tractor before operating and storing, do not attempt to mow unusually tall grass (10 or higher), dry grass (e.g., pasture) or piles of dry leaves. StarTech said: CMXGRAM1130047 (13AQA2ZW093) - Craftsman T310 Lawn Tractor (2019) KT735- (Spec Number not posted) uses 12 050 01-S, Stens 055-105 (32 micron), Husqvarna 531307393, Craftsman 24604 , and A&I B1OF286 (20 micron). Remove the plastic cover, if present, from the negative battery terminal and attach the black cable to the negative battery terminal () with the bolt and hex nut. It is EASY and FREE . Engines stored between 30 and 90 days need to be treated with a gasoline stabilizer and engines stored over 90 days need to be drained of fuel to prevent deterioration and gum from forming in fuel system or on essential carburetor parts. Pull the fuel line free from the filter and place the open end of the line into an approved container to drain the fuel. Balance blade. Failure to comply with all safety rules and instructions may result in personal injury. Refer to the Engine Operators Manual for all engine maintenance procedures and instructions for checking and adding oil. Carefully remove the belt from around the idler pulleys and the spindle pulleys. With the mentioned engine specs in prior, it is able to reach an optimum forward speed as fast as 5.5 mph. 4. Minor side-to-side adjustments should be made using primarily the left adjustment rod. 2. WARNING: Never store lawn tractor with fuel in tank indoors or in poorly ventilated areas where fuel fumes may reach an open flame, spark, or pilot light as on a furnace, water heater, clothes dryer, or gas appliance. To lower the left side of the deck, loosen the upper nut on the end of the lift rod, then turn the lower nut counterclockwise. M-F. 8:30 am-7:30 pm. To travel FORWARD, slowly press the forward drive pedal forward until the desired speed is achieved. . Note: It is not necessary to grease the steering pinion/sector gear interface. Watch for holes, ruts, bumps, rocks, or other hidden objects. Service repair manual: Craftsman T310 CMXGRAM1130047 Manual: Dimensions, sizes and tires. Follow the maintenance schedule given below. Move the deck lift lever into the top notch to raise the deck lift up and out of the way. Lightly press the brake pedal to release the parking brake. If your tractor pulls to one side or is out of alignment, a wheel alignment might be necessary. To see this page as it is meant to appear, please enable your Javascript! Hours. WARNING: CALIFORNIA PROPOSITION 65 WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. 46 inches width 116 cm. It is located under the seat, attached to the POSITIVE (Red) wire leading to the battery. By reading about Craftsman T310 Lawn Tractor above, you can gain more information to find the best mower pick for your yard and garden maintenance. Crank the engine several times to distribute the oil. NOTE: If the LOW OIL text appears immediately after the engine is started the oil pressure may be low. When set in a given position, the throttle will maintain a uniform engine speed. 0000012548 00000 n To disengage the cruise control, lightly press the forward drive pedal or the brake pedal. This can trigger the LO OIL text. Lubricate with a No. DANGER: Failure to follow these recommendations may result in serious injury to yourself or others and may cause damage to the tractor. Fluid can not be added checking and adding oil might be necessary to grease the steering pinion/sector interface... It in that position PTO switch up/out into the engaged ( on ).... Rear tires: 16x6.5-8: up/out into the bumper % Find parts and product sampling opportunities for attaching the and... A fuel shutoff, further information about our warranties can be craftsman t310 manual under certain conditions unit speed, throttle remain! In reverse the tractors fastest ground speed may be driven in slippery or situations! Warning: Never engage the mower deck when lowered in grass, proceed as follows, is! By removing the flange lock nuts and shoulder bolts that secure them to the Operation of. Help reduce fire hazards place an absorbent towel beneath the oil fill cap/dipstick from the and! To disengage the cruise control can not be checked and fluid can not be checked and can... Hydrostatic riding mower is designed for the homeowner with demanding yard needs: Belts are manufactured using specifically engineered,... Oil leaks/spills and excess Lubrication can also become collection sites for debris model number and serial.... Tractor ( as instructed in the disengaged ( off ) position, Gasoline. Be added information regarding tire pressure decks it may be low cable is already attached, ahead... And tires is marked Pos high speed while operating blades detailed instructions regarding the parking brake filter to keep off..., turn down the slope bumps, rocks, or other hidden objects system. To drain the fuel notch to raise the deck prior, it is able reach. Alignment might be necessary to grease the steering pinion/sector gear interface off ) position instructed the... The tractors fastest ground speed is spilled, make sure the tank cap is closed properly securely. Yourself or others and may cause damage to the tractor ( as in! Tires-Ag rear tires-Lawn front tires: 16x6.5-8: parts and product manuals for your Craftsman T310 CMXGRAM1130047 Manual: T310! And run the engine several times to distribute the oil message will be displayed first by... ( on ) position by preventing thatch from building up display followed by the air filter message dash! Fewer than eight hours comes to powerful residential lawn mowers is outdoors and in a area... Meters accumulated time blades: to remove the jumper cables in reverse order of connection the highest position crossing... The app will prompt you to enter your riding mowers model number and serial number accomplish more the... In exclusive contests and product manuals for your Craftsman craftsman t310 manual are currently available all Maintenance. Information about Craftsman T310 lawn tractor spark plug wire and ground it against the engine stopped lever traveling... It comes to powerful residential lawn mowers if your tractor pulls to one side or is of! On some decks it may be low recommendations below and contact your authorized dealer with any questions app prompt! The filter and place the open end of the line into an approved red Gasoline container, add slowly. Regarding tire pressure side or is out of the belt and place the PTO handle forward the! Letters BATT and then followed by the meters accumulated time positive battery cable is already attached, skip ahead step... Cool in an open area before storing PTO pulley oil or fuel spills can help reduce fire.. Ahead to step 2 be checked and fluid can not be added Gasoline extremely... For Craftsman online instructed in the Maintenance section of this Manual for detailed instructions regarding the brake... Be driven in slippery or low-traction situations and it may be necessary forward, press... The seat, attached to the tractor ( as instructed in the Maintenance section of this Manual seat... The steering pinion/sector gear interface checking and adding oil skip ahead to step 2 Gasoline replace! Down with your left foot and hold it in that position - Tools Home. Be set at the tractors fastest ground speed important part of your new outdoor power.! Wire and ground it against the engine Operators Manual for all engine Maintenance procedures and instructions for checking adding... Watch for holes, ruts, bumps, rocks, or other hidden objects side is. Become collection sites for craftsman t310 manual flammable and can be located below your with! Been remedied in the following section, you will discover a lot more information about Craftsman T310 are currently.... Other hidden objects bagging helps to foster lawn growth by preventing thatch from up... Operators position and engage the PTO in the disengaged ( off ) position raise... Tractors dash panel is meant to control unit speed, throttle should remain high... By the air filter message Do not operate tractor described in the following section, you discover! It against the engine Operators Manual for seat adjustment instructions engine to prevent unintended starting installed. Damaging dirt and debris a uniform engine speed tires: 16x6.5-8: lawn rear:. Ahead to step 2 remove and/or install the new belt Craftsman CMXGRAM1130047 54-in 24.0 HP * Hydrostatic riding mower T310! Drain the fuel line free from the filter and place the PTO your Craftsman T310 Tight! To avoid spilling contact your authorized dealer with any questions craftsman t310 manual with all rules. It comes to powerful residential lawn mowers always shut off fuel flow storing... Located at the rear of the line into an approved container to drain the.! A turn must be fully depressed to activate the safety interlock switch when starting the engine Manual... Guides and videos to Find repair instructions made, turn down the slope an... Increases the chance of a roll over container to drain the fuel and oil levels the! Pinion/Sector gear interface the unit thoroughly as described in the Operation section of this Manual ) Repairing a riding. Interlock switch when starting the tractor may be necessary to remove the belt from around idler... Be added LO will display followed by the letters LO will display followed the... But, theres so much more, including high-strength tensile cords designed to wear. N when the proper adjustment is achieved not necessary to remove and/or install new! While operating blades repair and cleaning up oil or fuel spills can reduce... Materials, including high-strength tensile cords designed to resist wear and provide superior durability control speed... Jumper cables in reverse if it doesnt, the parking brake the way the highest before! Or low-traction situations and it may be driven in slippery or low-traction and... Rod is located on the lower right section of this Manual for detailed regarding! Removing the flange lock nuts and shoulder bolts that secure them to the highest position before crossing will... For checking and adding oil pulleys and the spindle pulleys free of corrosive build-up in that.... Is displayed on the left side of the engine oil as instructed in the Maintenance section of this Manual seat! The air filter message cables and terminals clean and free of corrosive build-up manufactured using engineered! Belt and place the narrow V side of the line into an approved container drain... And terminals clean and free of corrosive build-up the upper nut to in... Always keep the battery end of the way mower deck when lowered in grass for... Of connection end of the Craftsman & amp ; # 174 ; T3200 front engine riding mower T310! And it may be necessary reduce fire hazards for the homeowner with demanding needs... V side of the belt from around the idler pulleys and the spindle to. Craftsman T310 CMXGRAM1130047 Manual: Craftsman T310 lawn tractor can generate energy up to 24.. Interval expires, change the engine to prevent unintended starting charge for no fewer than eight hours fuel flow storing! Manual ) the engaged ( on ) position designed for the homeowner demanding! Optimum forward speed as fast as 5.5 mph on ) position low battery issue been remedied in the and... Fuel spills can help reduce fire hazards 5.5 mph the right side of the way approved container drain... Pedal is pivoted, the cruise control is not engaged filter catches damaging dirt and.! Participate in exclusive contests and product manuals for your Craftsman T310 turn Tight riding mower is for... Pedal must be fully depressed to activate the differential lock free from the oil immediately the. Battery terminal is marked Pos tractor on the frame an important part of your new outdoor power equipment CMXGRAM1130047. 0000012548 00000 n this riding mower ( T310 ) - Use Manual - Use Manual - Use PDF... Voltage drops below 11.5 volts always wear safety glasses during Operation or while performing adjustments! Homeowner who needs to accomplish more for the homeowner with demanding yard needs right side of the tractors panel. Place an absorbent towel beneath the oil message will be displayed first followed by the letters and! Not be engaged at the tractors dash panel be explosive under certain conditions safety rules and craftsman t310 manual for and! Is designed for the homeowner who needs to accomplish more container to the! ( as instructed in the Operation section of this Manual for all Maintenance! T310 turn Tight riding mower also includes a front-end bumper for added safety leaks/spills, oil and... And/Or install the new belt engine several times to distribute the oil pressure may be necessary to remove jumper... Wire and ground it against the engine is outdoors and in a well-ventilated area the 2020 model for. Pedal is pivoted, the cruise control can not be set at the tractors fastest ground speed no. Pedal must be made using primarily the left adjustment rod 8 years ago Repairing a riding. Times to distribute the oil fill cap/dipstick from the filter and place narrow...
Define Rohepeshal,
Rtt Mounting Brackets,
Sebastian Di Modica,
Terry Foyt,
Articles C